Home page

Product Series

Foshan, Guangdong, China

SK85(SK5) high carbon steel coil / strip

SK85 (SK5) steel is Japanese high-grade carbon tool steel, cold work die steel, high carbon steel with a mass fraction of carbon above 0.80%. SK85 (SK5) steel hardness after quenching is 50~60HRC. It has high hardness, excellent wear resistance, and easy spheroidization.

Get ln Touch

C75S 1074 steel coil

C75S steel is a high-carbon spring steel known for its good elasticity and tensile strength. The “S” in its designation indicates it is of a special quality, often with stricter controls on impurities like sulfur and phosphorus. The key C75S properties of high hardness and flexibility are developed through quenching and tempering.

Get ln Touch

SK95(SK4) T10 high carbon steel coil

SK95(SK4) steel is the most common carbon tool steel with moderate toughness and low production cost. After heat treatment, SK95(SK4) steel hardness can reach 58-60HRC. However, this steel has low hardenability and poor heat resistance (250°C). It is not easy to overheat while still maintaining a fine grain.

Get ln Touch

1566 65Mn spring steel coil

65Mn steel is a spring steel used for various flat and round springs, cushion springs, spring springs, etc. in small sizes.Manganese in 65Mn improves hardenability, φ12mm steel can be hardened in oil, the surface decarburization tendency is smaller than silicon steel, and the comprehensive mechanical properties after heat treatment are better than carbon steel, but it has overheating sensitivity and temper brittleness.

Get ln Touch

S60C 1059 medium-to-high carbon steel coil

S60C steel is a medium-to-high carbon grade. It is chosen for applications that need greater strength and wear resistance than S50C. Heat treatment is required to achieve the key S60C properties, such as very high hardness. However, this also makes the it more difficult to machine and weld.

Get ln Touch

S50C 1050 medium carbon steel coil

S50C steel is a medium carbon steel offering higher strength and wear resistance than S45C. Through heat treatment, it can achieve a hard, wear-resistant surface, making it excellent for more applications. The primary trade-offs for this performance are reduced toughness and more difficult machining and welding. As its hardenability is limited, it is best applied to components of small to medium size.

Get ln Touch

75Cr1 steel coil

75Cr1 steel is a high-carbon alloy steel known for its high hardness and excellent wear resistance after heat treatment.The addition of chromium facilitates the heat treatment process and allows higher hardness to be achieved than the standard C75 Carbon Steel. The key 75Cr1 properties of a sharp, durable edge and good toughness are developed through a careful quenching and tempering process.

Get ln Touch

SKS51 Alloy tool steel coil

SKS51 steel is a common alloy tool steel, valued for its good combination of toughness and wear resistance. Its key SKS51 properties are developed through heat treatment, which imparts high hardness suitable for cutting and forming tools. The addition of nickel and chromium makes this SKS51 material tougher than standard carbon steels.

Get ln Touch

S45C 1045 medium carbon steel coil

S45C steel is a high-quality medium carbon steel known for its excellent balance of strength, toughness, and cost-effectiveness. It possesses good machinability in its annealed or normalized state, making it easy to process. However, it has limited hardenability, making it less suitable for large cross-section components.

Get ln Touch

51Crv4 Spring steel coil

51CrV4 spring steel is a well-known alloy steel, specifically designed for high-performance applications. The key 51CrV4 properties of high strength, excellent toughness, and fatigue resistance are developed through heat treatment. It has high fatigue strength, high yield ratio, but poor weldability, low plasticity due to cold deformation.

Get ln Touch

80CrV2 steel coil

80CrV2 steel is a highly regarded alloy tool steel, prized for its exceptional toughness and fine edge-holding capabilities. The key 80CrV2 properties, including high durability and good wear resistance, are derived from its carbon content combined with chromium (Cr) and vanadium (V). It must be properly heat-treated to achieve its full potential, making it significantly tougher and more resilient than simple high-carbon steels like the AISI 10xx series.

Get ln Touch

S65C 1064 spring steel coil

S65C steel is a common high-carbon steel used for parts requiring good strength and wear resistance. Heat treatment is necessary to develop its key S65C properties, such as hardness and resilience. Under the same surface state and complete hardening, the fatigue limit is not worse than that of alloy spring steel. However, the high carbon content makes this S65C material difficult to machine and weld.

Get ln Touch

< 1 2 >

Can't find the product you need?

Please contact us to provide you with satisfactory products and become a reliable supplier and service provider in the industry

GET IN TOUCH

Product Category

→ Silicon Steel

→ Medium-High Carbon Steel

→ Cold Rolled Steel

→ Galvanized Steel

→ Stainless Steel

E-mail: contact@weizhanmetal.com
WhatsApp: +86-13822142629

Tel: +86-13822142629

Landline: +86-757-2239 8011

Fax: +86-757-2239 8056

P.C.: 528311

ADD: No. 1 Weiye Road, Beijiao Town, Shunde District, Foshan, Guangdong China 528311.

WeChat

【 Business license】

Inquiry

Inquiry：→

Whatsapp

Whatsapp：+86 13822142629

Email

Email：contact@weizhanmetal.com

Tel

Tel：+86-13822142629